Shipping will be postponed due to production reasons from 11th December (in Japan) to a new, still undecided date, we will post new infos when they are available.

58584 1/10 RC TT-02D Drift Spec Chassis Kit
TT-02 drift tuned chassis kit!
Good balance to the left battery, was laid out in portrait orientation to the right motor driving stability by design, by the left and right common review and number of parts, and set beginners new standard with high maintainability and ease of freshly see TT-02. The finish on the properties it is easy to drift based on this chassis chassis Kit has appeared as early. Combined with plated mesh wheel in addition to the drift tires were combined, full ball bearings, sport motor, CVA oil dampers. A as a new design further strengthening to match the drift motor heat sink, powerful plastic parts were also standard equipment. Blue, block the battery holder also visually and silver plated brake disk type wheel hub.
TT-02D standard parts
★ OP.1476 TT-02 full bearing set
★ SP.746 CVA Damper Super Mini × 2
★ OP.1020 super drift tire (24mm width) × 2
★ OP.1571 TT-02 Aluminum Motor Heat Sink (Released in February)
★ Reinforced resin type TT-02 A parts × 2
★ OP.68 RS-540 Sport Tuned Motor

58588 1/10 RC Toyota FJ Cruiser (CC-01 chassis)
Popular in an individual style reflecting the image of a great car Land Cruiser FJ40 Toyota FJ Cruiser appeared in the CC-01 chassis!
Launched as a private vehicle in North America in 2006 , to hold the deep-rooted fan is released in Japan in 2010 Toyota FJ Cruiser. It has the image of a great car Land Cruiser FJ40 that has been loved all over the world, front down cormorant oval grille and round headlights, fender it leaves paste has been reproduced the very best in polycarbonate design. Cross-country chassis CC-01 that employs a full-time 4WD. The suspension, front double wishbone type, lower H arm , rear adopt guide, CVA oil dampers of four excellent shock absorbency. Rear axle within can also be assembled to lock specification, high drivability on rough path fun of control. It is possible to be equipped with LED lights (sold separately) to the front and rear.

58585 1/10 RC RC Alfa Romeo 155 V6 TI Jagermeister (TT-02 chassis)
57870 1/10 XB RC Alfa Romeo 155 V6 TI Jagermeister (TT-01 chassis TYPE-E)
To take advantage Entries 1994 German Touring Car Championship (DTM) among Alfa Romeo 155V6TI that showed the thermocline and mode for a long time
relationship with Star sports deep brewing maker Jaegermeister became the main sponsor, the 1/10RC car appears. Leave the image of commercial vehicles on the front grille slightly , sky form of the force that is significantly modify the power, the thin mark of deer bol character sponsor characteristic
stickers also realistic. The assembly in the assembly kit and maintenance is a simple, driving performance is enough shaft dry by adopting the TT-02 4WD chassis.

Please note that all information is tentative until officially confirmed from Tamiya, INC. and no responsibility is taken for the correctness of this information.

Static
32577 1/35 Soviet 1.5t Cargo Truck 1941
35366 1/35 Ford G.P.A.
37015 Horch Kfz 15

RC
54554 OP1554 Lock block Tire & 2 piece 5-spoke wheels (CC-01)
54555 OP1555 TT-02 FRP battery plate and transponder Stay Set
54556 OP1556 TT-02B FRP front Damper Stay Set
54557 OP1557 TT-02B FRP Rear Damper Stay Set
54559 OP1559 TT-02 Low Friction Suspension Ball (4pcs.)
54571 OP1571 TT-02 Aluminum Motor Heat Sink)
54574 OP1574 TT-02 Aluminum Racing Steering Set
54575 OP1575 TT-02 Aluminum steering bridge

Mini 4WD
15472 GP472 FRP front Wide Stay (for Fully Cowled Mini 4WD)
15473 GP473 Aluminium Spacer Set (12/6.7/6/3/1.5mm)
15474 GP474 Mini 4WD Catcher (Mini 4WD)
18080 Bear Hawks RS (Super II Chassis)
18081 Daihatsu Copen RMZ (VS Chassis)
18082 Daihatsu Copen XMZ (Super II Chassis)
18637 Festa Jaunes (MA Chassis)
19438 Ray Stinger Premium (Super II Chassis)
95003 Boomerang RS Black Special (VS Chassis)
95004 HG AR Chassis Carbon Front Wide stay (2mm/Blue Lame)
95005 HG AR Chassis Carbon Rear Wide stay (2mm/Blue Lame)
95007 HG Carbon Multi Reinforced Plate for 13/19mm Roller (2mm/Blue Lame)
95013 Mantaray Mk.II Clear Body Set II (Mini 4WD Limited)
95014 Neo Falcon Clear Body Set II (Mini 4WD Limited) (Mini 4WD)

Tools
74117 Tweezers to bend (for Etching Parts)
87153 HG Precision Brush Ultra-Super Slight
87154 HG Precision Brush Super Slight
87155 HG Precision Brush Slight
87156 HG Precision Brush Small
87157 HG Precision Brush Super Small
87158 HG Precision Brush Small
87159 HG Precision Brush Middle

Please note that all information is tentative until officially confirmed from Tamiya, INC. and no responsibility is taken for the correctness of this information.

Static
12655 1/6 Harley-Davidson Fat Boy Lo Detail Up Parts Set
25167 1/48 Mitsubishi A6M5 Zero Fighter Model 52
25168 1/72 Mitsubishi A6M5 Zero Fighter Model 52
25169 1/72 Mitsubishi A6M3 Zero Fighter Model 21

RC
51541 GAZOO Racing TRD 86 Spare Body
84372 1/10 RC Avante 2001 Body Parts Set
84374 TRF201X Lightweight Body

51557 TRF418 Spur Gear (116T)
51558 TRF418 Front Belt (169T)
51559 TRF418 Rear Belt (63T)

54550 TT-02 Low Friction 3x18mm stepped bis (2 pcs.)
54551 6 spoke two-piece wheel (2pcs.) (26mm width +2) (Red Plating)
54552 6 spoke two-piece wheel (2pcs.) (26mm width +4) (Red Plating)
54553 6 spoke two-piece wheel (2pcs.) (26mm width +6) (Red Plating)
54558 TT-02 Aluminumnum Motor Mount
54568 TRF418 C Parts (Carbon Reinforcement Front Up Light)
54569 TRF418 D Parts (Carbon Reinforcement Suspension Arms)
54570 TRF418 E Parts (Carbon Rear Up Light)

42261 TRF 04 Hard coat Aluminum Pinion Gear (31T)
42262 TRF 04 Hard coat Aluminum Pinion Gear (32T)
42263 TRF 04 Hard coat Aluminum Pinion Gear (33T)
42264 TRF 04 Hard coat Aluminum Pinion Gear (34T)
42265 TRF 04 Hard coat Aluminum Pinion Gear (35T)
42266 TRF 04 Hard coat Aluminum Pinion Gear (36T)
42267 TRF 04 Hard coat Aluminum Pinion Gear (37T)
42268 TRF 04 Hard coat Aluminum Pinion Gear (38T)
42269 TRF 04 Hard coat Aluminum Pinion Gear (39T)
42272 TRF Short Damper HL Cylinder (2pcs.)
42273 TRF Short Damper (Black hard coat) (4pcs.)

Mini 4WD
18062 Vanquish RS (VS Chassis)
94823 Mini 4WD HG Aluminumnum Setting Board
94859 13mm All Aluminumnum Bearing Roller (Blue)
94860 13mm All Aluminumnum Bearing Roller (Red)
95006 Blade Wait (Silver) w/FRP Multi Roller Setting Stay

Please note that all information is tentative until officially confirmed from Tamiya, INC. and no responsibility is taken for the correctness of this information.

Tamiya 58583 1/10 RC Egress 2013

Machine longing to match the RC scene of current, increased the potential
Avante that appeared in 1988 as the highest models of 4WD buggy. TRF (Tamiya Racing Factory) was formed in the following year, Tamiya has taken the first step to challenge the race in the world. The new design as a racing car based on intake, the Avante the know-how obtained in the race, I adopt a carbon plate that was used in aircraft and F1, you can use up expensive titanium bis large capacity oil shocks and ball differential, lightweight, It is the egress has been developed aiming to win the race. At that time, in the belt drive car prime, egress that was active in the race as a shaft drive cars only, revived by potential up the parts to fit the RC the current scene.

– Shaft-driven 4WD chassis with high rigidity and using lots of carbon parts]　chassis carbon double deck. I am proud of the high rigidity that does not budge even twist. Power train of motor shaft drive 4WD Full ball bearings vertically. Ball diff front and rear new parts reviewing the original design. In addition to the smooth operation, it is up to both maintainability, durability. In addition, the built-in one-way bearing in the drive gear and show the straightforward handling by the torque splitter effect. It is also possible that instead of the one-way bearing, to lock specification. In addition, incorporating the same structure as the TRF series of current, universal shaft to be abused most drive system you’ve got a high reliability and smooth drive. Independent suspension 4-wheel double wishbone. Equipped with four oil damper employing the aluminum cylinder, stabilizer also mounted on the front and back. Front upright is aluminum cutting made ​​of high strength. Equipped with ball bearings to the wiper arm shaft, steering system produces a linear handling with the carbon plate of 2.0mm thickness. Titanium bis does not employ this time, but I realize the performance improvement of about more than make up. In the brushless motor current mainstream, you can enjoy a wonderful run.

Secure traction by using the one-way ball differential of the new design, the center back and forth.

Aluminum cap high oil damper in double wishbone suspension.

Carbon double deck chassis 15mm stretched the wheelbase to Avante, enhanced driving stability.

Basic Specifications

★ frame = carbon double deck ★ Drivetrain: Shaft-driven 4WD ★ Body under cowl = polycarbonate ★ Front = before and after ★ Length: 430mm, Width 243mm, Height: 157mm ★ Wheelbase: 275mm ★ Tread = front, the rear both ball differential, center one-way ★ Steering: 3-piece tie rod ★ Suspension: 4-wheel double wishbone ★ Tire Width / Diameter = Front 32/88mm, 40/88mm ★ rear damper = aluminum cylinder cap made ​​by high oil dampers ★ Gear Ratio = 8.25 : 1 (22T pinion gear kit) ★ 540 type motor (sold separately) ★ Speed ​​controller = ESC specification (sold separately)

Manual download

16038 1/6 Police 1200 Harley-Davidson FLH type

Fearless motorcycle specification to symbolize the highway of America
Private type is used as a Detroit police for already in 1908 there is no start-ups, motorcycles Harley-Davidson Inc., equipped with equipment for police use in 1921 further Police first type were made. Electra Glide FLH1200 is one of the top model to represent the Harley’s in the 1970s, but it is equipped with V-twin engine boasts a displacement of 1200cc as its name the “shovel head”. It was what is full of personality that bulk-long total length 2.4m, also weight 300kg or more and imposing like big bike. Result of improvements stacked basic form that appeared in 1941 “FL model” since, I show excellent stability up to the high speed from low speed by the engine with a room that has the durability and unrivaled high reliability, easy to handle further. United States, not to mention I was working as a police motorcycle in the world.

About the Model
This is a precision plastic model assembly kit reproduced in 1/6 scale motorcycle specifications ★ Harley-Davidson FLH1200. ★ about 400mm total length, about 185mm width. ★ plastic parts are composed of chrome-plated parts and molded white color, such as gray, matte. Beautiful finish can enjoy. ★ metal handle, brake disc, such as muffler protector. Synthetic rubber sheet, such as grip. ★ I reproduce to realize the full equipment of the police specification only saddle and windshield, warning light, such as radio box large. ★ mechanical siren on the left side muffler top also modeled. ★ I’ve prepared a slide mark and meter display and “POLICE” logo fender. ★ I started before and after suspension, you can enjoy such as brake pedal and the side stand of the return spring with, also the operation of each part. ★ Gotae enough also made ​​air-cooled V-twin engine with the nickname of the shovel head. ★ tire hollow rubber with a texture. Tread pattern, of course, I was reproduced in sculpture to character of the side wall. .
Package

★ Reproduce to realize the full equipment of the police specification only radio box and warning lights, such as saddle bags.
★ Mechanical siren which is mounted on the rear wheel, helmet that can be used as part of accessories as well.
★ Harley-only, air-cooled V-twin engine finish of precision full of a feeling. Use plated parts to muffler and air cleaner cover.
★ Reproduced without the speaker box and windshield of such large, leaving the police for equipment.
★ Fire extinguisher is also modeled as an accessory part.
★ Character and “POLICE” and “STATE”, and meter display is provided by the slide mark.

16039 1/6 Harley Davidson FXE 1200 Super Glide

Founder of Factory Chopper, 1975 model Super Glide
Including Big Machine big machine in was told the 1970s, the King of the motorcycle, the FLH80 classic and FLH1200, Harley-Davidson, has been producing motorcycles of various kinds directly below. Top model of sport type of company was FXE1200 super glide among them. Super Glide production was started from 1971 is equipped with air-cooled 4-stroke OHV · V twin 1207cc engine called FLH1200 in common with the “shovel head”. The frame is also used double cradle the same type as the FLH basically. On the other hand, spoke wire wheels and front fork, and narrow headlights is something which is based on parts of a light XL Sportster. Super Glide that pioneer of the genre of sports touring is produced until 1978, and it was with roots custom style genuine manufacturer of “factory chopper”. FXDB Dyna Sturgis 1991 and FXS Low Rider, of 1977 which attracted worldwide popularity will take over the seat, as the founder of the family on behalf of Harley-current lineup, the pedigree has been handed down.

About the Model
Opened up a new genre of sports ★ touring, the 1975 model Harley-Davidson Super Glide FXE1200, This is a plastic model assembly kit of the 1/6 scale. ★ total length 389mm. ★ accurately reproduced ranging engine, the wheel from the frame. I can enjoy the assembly in making Gotae. ★ Gotae making plentiful was reproduced precisely as well as carburetor and spark plug including delicate cooling fins “shovel head” OHV · V twin engine. ★ Front and rear suspension is working smoothly equipped with a coil spring. ★ tail light you have beautifully carved the lens cut, turn signal. ★ oil tank under the seat is reproduced battery of course. ★ wire spoke wheel tightens plated parts, the feet. ★ The transparent parts and decals, the meter finish of feeling full. ★ side stand collapsible with a return spring. ★ tire hollow rubber Realistic which reproduced the exact tread pattern.
Package

★ Reproduce to realize fully the slim form of the Super Glide was finished in chopper style.
★ Gloss air cleaner and tappet cover, such as muffler, engine using the plating parts of matte two worth seeing.
★ Turn signal and tail lamp with clear orange and clear red parts tightens the rear view.
★ Texture by a special plastic handle grips and seat, the change lever.
★ Fuel tank and small, twin-lens meter of speed and tachometer is sporty.
★ Harley logo and rainbow line of S-shaped painted on the fuel tank, such as the instrument panel provided by the slide mark.